Gears have teeth that mesh with other gears in order to transmit torque. Gears can be used to change the speed, torque (turning force), or direction of a motor’s original output. For gears to be compatible with each other, the meshing teeth must have the same shape (size and pitch). Gears are ideal for use in more compact spaces and are also used for changing the direction of rotation.
Gears offer more flexibility in transforming motion than sprockets and chain because there are a larger variety of gear sizes available.
There are many different types of gears; one of the simplest and most commonly used is a spur gear, and that is the gear type used in the REV ION System. Spur gears consist of a disk with straight teeth projecting radially (outward from the center) and these gears will only mesh correctly with other gears if they are on parallel shafts.
Documentation Coming Soon!
All REV ION Gears are 20DP, made of 4140 Steel, and pocketed to reduce weight. Our REV ION 20DP Gears (Product Family Page) come in a wide range of sizes and bores including MAXSpline, 1/2in Hex, and 1/2in Rounded Hex. Larger gears include #10 clearance hole patterns, 2in bolt circle, and MAXTube mounting pattern.
DP stands for Diametral Pitch. The diametral pitch of a gear is the number of teeth in the gear for each inch of pitch diameter. So, a 20DP gear has 20 teeth per inch.
Sometimes in a design it may be desirable to stack together multiples of the same gear on a shaft to increase the load carrying capacity of the gears. In the case where the number of teeth on the gear is not divisible by six, because of how they are oriented when put onto the hex shaft, the teeth may not be aligned between the two gears. To ensure all of the gears are clocked the same way, use the alignment shaft notch to put all the gears on the shaft with the same orientation.
Meshing two or more gears together is known as a gear train. Selecting the gears in the gear train as larger or smaller relative to the input gear can either increase the output speed, or increase the output torque but the total power is not affected.
A gear ratio is the ratio of the sizes of two gears. For instance, in the image below, the input gear is a 15 tooth gear and the output gear is a 72 tooth gear. So, the gear ratio is 72T:15T. The ratio in size from the input (driving) gear to the output (driven) gear determines if the output is faster (less torque) or has more torque (slower). The gear ratio is proportional to the speed and torque changes between them.
In the image above, the 15 tooth input gear is rotating clockwise. As the input gear rotates, it pushes down on the output gear where the teeth are meshed. This action transmits the motion to the output gear, but forces the output gear to rotate in the opposite direction of the input gear.
When assembling the gear train we recommend adding grease during assembly and re-applying as needed for the maintenance of your mechanism. For most applications, using White Lithium Grease or Red Tacky Grease will provide sufficient lubrication.
In order for gears to work effectively, and not become damaged, it’s important that the center-to-center distance is correctly adjusted. The gears in DETAIL A of the figure below may work under very light load, but they will certainly not work and will skip under any significant loading. The gears in that example are too far apart, and the teeth of each gear barely contact each other. The gears in DETAIL B are correctly spaced and will provide smooth and reliable operation.
To learn more about calculating center-to-center distance for Gears visit the Center-to-Center Distance Section.
Gears are one common way to transmit power and change the output torque or speed of a mechanical system. Understanding these basic concepts is required to make optimized design decisions which consider the trade-off between torque and speed for a system with a given power.
Speed is the measure of how fast an object is moving. The speed of an object is how far it will travel in a given amount of time. For rotating parts like gears and wheels, speed is expressed in how many revolutions are made in a given amount of time. Under ideal conditions, the rotation of a wheel is converted into linear speed and can be calculated by multiplying the diameter of the wheel by the rotations for a given time. The SI unit for speed is meters per second (m/s), but speed is also commonly expressed in feet per second (ft/s).
Torque is roughly the measure of the turning force on an object like a gear or a wheel. Mathematically, torque is defined as the rate of change of the angular momentum of an object. This can also be stated as a force that acts normal (at 90 degrees) to a radial lever arm which causes the object to rotate. A common example of torque is the use of a wrench in order to tighten or loosen a bolt. In that example, using a longer wrench can produce more torque on the bolt than using a shorter wrench. Torque is commonly expressed in Nâ‹…m or inâ‹…lbs.
When torque is turning an object like a spur gear, the gear will create a straight line (linear) force at the point where the teeth contact the other gear. The magnitude of the torque created is the product of the rotational force applied and the length of the lever arm ,which in the case of a gear, is half of the pitch diameter (the radius).
Power (P) is the rate of work over time. The concept of power includes both a physical change and a time period in which the change occurs. This is different from the concept of work which only measures a physical change. The difference in these two concepts is that it takes the same amount of work to carry a brick up a mountain whether you walk or run, but running takes more power because the work is done in a shorter amount of time. The SI unit for power is the Watt (W) which is equivalent to one joule per second (J/s).
In competitive robotics, the total amount of available power is determined by the motors and batteries allowed to be used. The maximum speed at which an arm can lift a certain load is dictated by the maximum system power.
Meshing two or more gears together is known as a gear train. Selecting the gears in the gear train as larger or smaller relative to the input gear can either increase the output speed or increase the output torque, but the total power is not affected.
When a larger gear drives a smaller one, for one rotation of the larger gear the small gear must complete more revolutions - so the output will be faster than the input. If the situation is reversed, and aa smaller gear drives a larger output gear, then for one rotation of the input the output will complete less than one revolution – so the output will be slower than the input. The ratio of the sizes of the two gears is proportional to the speed and torque changes between them.
The ratio in size from the input (driving) gear to the output (driven) gear determines if the output is faster (less torque) or has more torque (slower). To calculate exactly how the gear ratio effects the relationship from input to output, find the ratio for the number of teeth between the two gears. In the image below, the ratio of the number of teeth from the input gear to the output gear is 72T:15T which means the input needs to turn 4.8 rotations for the output to complete one rotation.
What happens when a 45 tooth idler gear is inserted into the gear example? An idler gear is any intermediate (between input and output) gear which does not drive any output (work) shaft. Idler gears are used to transmit torque over longer distances than would be practical by using just a single pair of gears. Idler gears are also used to reverse the direction of the rotation of the final gear.
Regardless of the number or size of idler gears in the chain, only the first and last gear determine the reduction. Since idler gears do not change the gear reduction, the reduction in the example remains 72:15, but the direction of the output stage is now reversed from the previous example.
Idler gears are a good way to transmit power across distances in your robot. A common example of this is an all gear drivetrain. In this example the gears on the end are linked to the drive wheels and one of the center gears would be driven by a motor (not shown). The orange arrows indicate the relative rotation of each of the gears showing that the two wheels are mechanically linked and will always rotate in the same direction.
Because idler gears reverse the direction of rotation, it is important to pay attention to the number of gears in the drivetrain. In the picture below there is an even number of gears, and because of this the wheels will always spin in the opposite direction.
Some designs may require more reduction than is practical in a single stage. The ratio from the smallest gear available to the largest in the REV ION Build System is 80:10, so if a greater reduction than 8 is required, multiple reduction stages can be used in the same mechanism, and this is called a compound gear reduction. There are multiple gear pairs in a compound reduction with each pair of gears linked by a shared shaft. Below is an example of a two-stage reduction. The driving gear (input) of each pair is highlighted in orange.
Reduction is the concept of lowering input speed to reduce overall output speed.
To calculate the total reduction of a compound reduction, identify the reduction of each stage and then multiply each reduction together.
​Where:
CR is the total Compound Reduction
Rn is the total reduction of each stage
Using the image above as an example, the compound reduction is 12:1.
​For any gear system, there are a limited number of gear sizes available, so in addition to being able to create greater reductions using compound reductions, it is also possible to create a wider range of reduction values, or the same reduction of a single stage, but with smaller diameter gears.
To ensure that you have a proper amount of gear teeth mesh, it is important to calculate the center-to-center distance in between your gears. You can do this by first calculating the pitch diameter (PD) of each gear using some combination of module (M), number of teeth (N), or outside diameter (OD).
PD = M × N
PD = (OD × N) / (N + 2)
PD = OD - (2 × M)
Then, use the pitch diameters to calculate the center-to-center distance (CCD).
CCD = ((PD1) / 2) + ((PD2) / 2)
Any two REV ION gears that add up to 80 teeth will fit center-to-center on structure elements featuring the MAX Pattern and have a center-to-center distance of 2in
Documentation Coming Soon!
