LogoLogo
  • REV ION Build System
  • FRC Robot Basics Guide
  • System Standards
  • Structure
    • Introduction to Structure
    • Brackets
      • MAXSpline Brackets
      • Structure Brackets
      • Actuator Brackets
    • MAX Pattern Plates
    • Hardware
    • Extrusion
    • Bumper Brackets
    • MAXComposite
  • Motion
    • Introduction to Motion
    • Shafts / Spacers / Collars
    • MAXHubs
    • Tubes / Bushings / Axles
    • Bearings / Bearing Blocks
    • Pivot Joints
    • Linear Actuators
    • Gears
      • Advanced Gears
    • Sprockets and Chain
      • Advanced Sprockets and Chain
      • Chain Tool
    • Belts and Pulleys
    • Ratio Plates
    • NEO Brushless Motors
    • Servos
      • Smart Robot Servo
    • Wheels
      • Traction
      • Grip
      • Omni
      • Compliant
      • Flap
    • Gearboxes
      • 2 Motor Gearbox - Through Bore
      • 2 Motor Drivetrain Gearbox - Through Bore
    • MAXPlanetary System
      • System Features
      • Mounting Features
      • Load Ratings
      • Assembly Tips and Tricks
    • MAXSwerve
      • MAXSwerve Build Guide
      • MAXSwerve Drivetrain Onshape
      • MAXSwerve Calibration
      • Wiring MAXSwerve
      • Programming MAXSwerve
      • MAXSwerve Wheel V1 Evaluation
      • MAXSwerve Module Inspection
      • Aluminum MAXSwerve Wheels
      • MAXSwerve Wheel Tread Reinforcement
  • Onshape Examples
    • Onshape CAD Examples
    • Low Complexity
    • Medium Complexity
    • High Complexity
  • Building Techniques
    • Supporting Motion
    • Constraining Motion
  • Build Guides
    • MAXSwerve Module Assembly
      • Motor Orientation
      • MAXSwerve SPARK MAX Mounting Bracket Assembly
      • MAXSwerve Pack Contents
      • MAXSwerve Assembly Tips
    • MAXSwerve Drivetrain Assembly
    • Elevator Bearing Block Assembly
    • MAXPlanetary Gearbox Assembly
      • NEO & CIM
      • NEO Vortex
      • NEO 550 & 550 Sized Motors
      • 775 Sized Motors
      • Falcon
      • Shaft Retention Assembly
      • Spacer Installation
    • MAX 90 Degree Gearbox Assembly
    • 2 Motor Drivetrain Gearbox Assembly
    • 2 Motor Gearbox Assembly
    • Linear Actuator Assembly
    • MAX 180 Degree Gearbox Assembly
    • Drivetrain Bumper Kit Assembly
      • West Coast Drivetrain with MAXTube
      • AM14U5 (FRC Kit of Parts Chassis)
    • REV ION West Coast Drivetrain Assembly
  • REV ION Control System
    • REV Hardware Client
    • Power Distribution Hub
    • Radio Power Module
    • Mini Power Module
    • Brushless Motors and Controllers
    • Pneumatics
    • Sensors & Indicators
Powered by GitBook
On this page
  • 2 Motor Gearbox - Through Bore Assembly Instructions
  • Greasing Guide
  • NEO Vortex vs. NEO Brushless Motor
  • Base Subassembly
  • Motor Shaft Subassembly (Gear Ratios 1:1, 2:1, or 3:1)
  • Motor Shaft Subassembly (Gear Ratios 5:1 and 6:1)
  • Outer Plate Assembly

Was this helpful?

Export as PDF
  1. Build Guides

2 Motor Gearbox Assembly

Previous2 Motor Drivetrain Gearbox AssemblyNextLinear Actuator Assembly

Last updated 22 days ago

Was this helpful?

2 Motor Gearbox - Through Bore Assembly Instructions

Greasing Guide

When assembling the 2 Motor Gearbox we recommend adding grease during assembly and re-applying as needed for the maintenance of your mechanism. For most applications, using or will provide sufficient lubrication.

When applying the grease of your choice, add a small amount to the gearbox’s gears, ensuring that it gets evenly distributed throughout the system.

NEO Vortex vs. NEO Brushless Motor

The below instructions show the assembly of the 2 Motor Gearbox with two NEO Brushless Motors. The 2 Motor Gearbox can be assembled with two NEO Vortex with 8mm Vortex Shafts following the same instructions.

Base Subassembly

1) Install one of the Flanged Bearings into the Motor Plate.

2) Insert the two motors into the back side of the Motor Plate, and fasten them into place using two 1/2in long 10-32 button head screws per motor.

3) Insert the end of the Through Bore Shaft into the bearing. The shoulder of the shaft should be fully seated against the face of the bearing.

4) Slide one of the 1/8in long MAXSpline spacers onto the through bore shaft.

6) Slide one 1/8in long and one 1/4in long MAXSpline spacer onto the through bore shaft. Ensure that the stack of spacers and the gear are pressed firmly together and that the end of the last spacer is flush with the shoulder at the end of the through bore shaft.

7) Install the motor shaft key into each of the motors.

If you are utilizing Gear Ratio 5:1 or 6:1, See the following:

Motor Shaft Subassembly (Gear Ratios 1:1, 2:1, or 3:1)

1) Install the 1/2in Hex Adapter onto each of the motor shafts.

2) Slide one 1/16in long and one 1/4in long 1/2in Hex Shaft Spacers onto each of the Hex Adapters.

3) Slide the appropriate 1/2in Hex Bore Gear for the selected ratio onto each of the Hex Adapters. Ensure that the gears are properly meshed with the center gear.

4) Slide an 8mm Shaft Spacer onto the end of each of the motor shafts.

5) Install an external retaining ring on the end of each motor shaft to hold the shaft stack-up into place.

Motor Shaft Subassembly (Gear Ratios 5:1 and 6:1)

1) Slide an 8mm Shaft Spacer onto each of the motor shafts.

2) Install the appropriate motor pinion for the selected ratio on each motor shaft. Ensure that the pinions are properly meshed with the center gear.

3) Install an external retaining ring on each motor shaft to hold the pinion in place.

Outer Plate Assembly

1) Install the remaining Flanged Bearing in the Outer Plate. The flange of the bearing should be on the opposite side of the plate from the screw head cutouts on the corners of the plate.

2) Place the Outer Plate and bearing onto the through bore shaft with the bearing flange facing inwards.

3) Slide the four 1-1/8in long #10 spacers in between the Outer Plate and Motor Plate, and line them up with the four corner holes in the Outer Plate.

4) Insert the four 1-1/2in long 10-32 button head screws through the Outer Plate, through the #10 spacers, and into the threaded holes in the Motor Plate. Leave the screws slightly loose.

5) Rotate the gearbox shaft a few times and then tighten the screws. Test spin the gearbox to ensure that it rotates freely.

5) Slide the appropriate MAXSpline Gear for your selected ratio onto the through bore shaft. The appropriate gears to be used for your ratio can be found here:

White Lithium Grease
Red Tacky Grease
Motor Shaft Subassembly (Gear Ratios 5:1 or 6:1)
Ratio Gear Bundle Contents