LogoLogo
  • REV ION Build System
  • FRC Robot Basics Guide
  • System Standards
  • Structure
    • Introduction to Structure
    • Brackets
      • MAXSpline Brackets
      • Structure Brackets
      • Actuator Brackets
    • MAX Pattern Plates
    • Hardware
    • Extrusion
    • Bumper Brackets
    • MAXComposite
  • Motion
    • Introduction to Motion
    • Shafts / Spacers / Collars
    • MAXHubs
    • Tubes / Bushings / Axles
    • Bearings / Bearing Blocks
    • Pivot Joints
    • Linear Actuators
    • Gears
      • Advanced Gears
    • Sprockets and Chain
      • Advanced Sprockets and Chain
      • Chain Tool
    • Belts and Pulleys
    • Ratio Plates
    • NEO Brushless Motors
    • Servos
      • Smart Robot Servo
    • Wheels
      • Traction
      • Grip
      • Omni
      • Compliant
      • Flap
    • Gearboxes
      • 2 Motor Gearbox - Through Bore
      • 2 Motor Drivetrain Gearbox - Through Bore
    • MAXPlanetary System
      • System Features
      • Mounting Features
      • Load Ratings
      • Assembly Tips and Tricks
    • MAXSwerve
      • MAXSwerve Build Guide
      • MAXSwerve Drivetrain Onshape
      • MAXSwerve Calibration
      • Wiring MAXSwerve
      • Programming MAXSwerve
      • MAXSwerve Wheel V1 Evaluation
      • MAXSwerve Module Inspection
      • Aluminum MAXSwerve Wheels
      • MAXSwerve Wheel Tread Reinforcement
  • Onshape Examples
    • Onshape CAD Examples
    • Low Complexity
    • Medium Complexity
    • High Complexity
  • Building Techniques
    • Supporting Motion
    • Constraining Motion
  • Build Guides
    • MAXSwerve Module Assembly
      • Motor Orientation
      • MAXSwerve SPARK MAX Mounting Bracket Assembly
      • MAXSwerve Pack Contents
      • MAXSwerve Assembly Tips
    • MAXSwerve Drivetrain Assembly
    • Elevator Bearing Block Assembly
    • MAXPlanetary Gearbox Assembly
      • NEO & CIM
      • NEO Vortex
      • NEO 550 & 550 Sized Motors
      • 775 Sized Motors
      • Falcon
      • Shaft Retention Assembly
      • Spacer Installation
    • MAX 90 Degree Gearbox Assembly
    • 2 Motor Drivetrain Gearbox Assembly
    • 2 Motor Gearbox Assembly
    • Linear Actuator Assembly
    • MAX 180 Degree Gearbox Assembly
    • Drivetrain Bumper Kit Assembly
      • West Coast Drivetrain with MAXTube
      • AM14U5 (FRC Kit of Parts Chassis)
    • REV ION West Coast Drivetrain Assembly
  • REV ION Control System
    • REV Hardware Client
    • Power Distribution Hub
    • Radio Power Module
    • Mini Power Module
    • Brushless Motors and Controllers
    • Pneumatics
    • Sensors & Indicators
Powered by GitBook
On this page

Was this helpful?

Export as PDF
  1. Motion
  2. MAXPlanetary System

Mounting Features

PreviousSystem FeaturesNextLoad Ratings

Last updated 1 year ago

Was this helpful?

  • All 10-32 Screws used for Assembly and Mounting

  • 10-32 Face Mounting Holes on a 2in Bolt Circle with 2 Orientations

  • 2in Gearbox Height

    • Gearbox does not protrude above or below common FRC structural tubes

    • Output shaft stays on 1.0in pitch when the gearbox is mounted using the side holes

  • Side Mounting Holes are on a 0.5in pitch regardless of number of stages

MAXPlanetary Gearbox face mounted on 2x1 aluminum tubing
MAXPlanetary Gearbox side mounted on 1x1 aluminum tubing
An image of how a MAXPlanetary Gearbox would look mounted on 2x1 aluminum tubing.
An image of an example of a MAXPlanetary Gearbox mounted on the top of 1x1 aluminum tubing