LogoLogo
  • Introduction
  • Getting Started with Control Hub
    • Connect to the Robot Controller Console
    • Updating Wi-Fi Settings
    • Connecting Driver Station to Control Hub
    • Wiring Diagram
    • Next Steps
  • Getting Started with Driver Hub
  • Adding More Motors
    • SPARKmini Motor Controller
    • Adding an Expansion Hub
  • Troubleshooting the Control System
    • General Troubleshooting
    • Control Hub Troubleshooting
    • Driver Hub Troubleshooting
      • Driver Hub Battery Troubleshooting
    • Expansion Hub Troubleshooting
    • Status LED Blink Codes
  • System Overview
    • Control Hub Specifications
    • Expansion Hub Specifications
    • Driver Hub Specifications
    • Port Pinouts
    • Protection Features
    • Cables and Connectors
      • XT-30 - Power Cable
      • JST VH - Motor Power
      • JST PH - Sensors and RS485
    • Integrated Sensors
    • Dimensions and Important Component Locations
  • Updating and Managing
    • Managing Wi-Fi on the Control Hub
    • REV Hardware Client
    • Updating Firmware
      • Firmware Changelog
    • Updating Operating System
      • Control Hub Operating System Changelog
    • Updating Robot Controller Application
      • Updating Robot Controller Application via Android Studio
    • Updating the Driver Hub
      • Driver Hub OS - Change Log
    • Accessing Log Files
    • Android Studio - Deploying Code Wirelessly
  • Hello Robot - Intro to Blocks Programming
    • Welcome to Hello Robot!
    • Where to Program - Client vs. Browser
      • What is an OpMode?
    • Setting up a Configuration
      • Common Errors in Configuration
    • Using a Gamepad
    • Part 1: Tackling the Basics
      • Tackling the Basics Directory - Blocks
      • Creating an OpMode - Blocks
      • Programming Essentials
      • Programming Servos
        • Programming Servo Basics
        • Using a Gamepad with a Servo
        • Programming Servo Telemetry
      • Programming Motors
        • Programming Motors Basics
        • Programming a Motor with a Gamepad
        • Programming Motor Telemetry
      • Programming Touch Sensors
      • Programming Color Sensors
        • Color Sensor Telemetry
        • Detecting Color
    • Part 2: Robot Control
      • Robot Control Blocks Directory
      • Programming Drivetrain Motors
      • Arcade Style TeleOp - Blocks
        • Establishing Variables in Blocks
        • Motor Power vs. Robot Movement
        • Programming Arcade Drive
      • Arm Control - Blocks
        • Adding a Limit Switch
      • Robot Control Full Program
    • Part 3: Autonomous and Encoders
      • ElapsedTime - Blocks
        • ElapsedTime Setup
        • ElapsedTime Logic
        • ElapsedTime - Multiple Movements
      • Encoder Basics
      • Drivetrain Encoders - Blocks
        • Converting Encoder Ticks to a Distance
        • Moving to a Target Distance
        • Setting Velocity
        • Turning the Drivetrain Using RUN_TO_POSITION
      • Arm Control with Encoders - Blocks
        • Estimating the Position of the Arm
        • Calculating Target Position
        • Using Limits to Control Range of Motion
    • Part 4: Going Beyond!
      • Exploring Functions
      • Programming Mecanum - Simplified
      • Programming Mecanum - Refined
  • Hello Robot - Intro to OnBot Java Programming
    • Welcome to Hello Robot!
    • Where to Program - Client vs. Browser
      • What is an OpMode?
    • Setting up a Configuration
      • Common Errors in Configuration
    • Using a Gamepad
    • Part 1: Tackling the Basics
      • Tackling the Basics Directory - OnBot
      • Creating an OpMode - OnBot
      • Programming Essentials
      • Programming Servos
        • Programming Servo Basics
        • Using a Gamepad with a Servo
        • Programming Servo Telemetry
      • Programming Motors
        • Programming Motor Basics
        • Programming a Motor with a Gamepad
        • Programming Motor Telemetry
      • Programming Touch Sensors
    • Part 2: Robot Control
      • Robot Control OnBot Java Directory
      • Programming Drivetrain Motors
      • Arcade Style TeleOp - OnBot Java
        • Establishing Variables in OnBot Java
        • Motor Power vs. Robot Movement
        • Programming Arcade Drive
      • Arm Control - OnBot Java
        • Adding a Limit Switch
      • Robot Control Full Program
    • Part 3: Autonomous and Encoders
      • ElapsedTime - OnBot Java
        • ElapsedTime Setup
        • ElapsedTime Logic
        • ElapsedTime - Multiple Movements
      • Encoder Basics
      • Drivetrain Encoders - OnBot Java
        • Converting Encoder Ticks to a Distance
        • Moving to a Target Distance
        • Setting Velocity
        • Turning the Drivetrain Using RUN_TO_POSITION
      • Arm Control with Encoders - OnBot Java
        • Estimating the Position of the Arm
        • Calculating Target Position
        • Using Limits to Control Range of Motion
  • Sensors
    • Introduction to Sensors
    • Digital
    • Analog
    • I2C
      • IMU
        • Orientating the IMU
      • Adding an External IMU to your Hub
    • Encoders
      • REV Motor Encoders
      • Through Bore Encoder
    • Using 3rd Party Sensors
      • Sensor Compatibility Chart
  • Useful Links
    • REV DUO Build System
  • Legacy Documentation
    • Configuring Your Android Devices
    • Expansion Hub with Android Device Robot Controller
      • Driver Station and Robot Controller Pairing
      • Wiring Diagram
      • Configuration
    • REV Hub Interface Software
Powered by GitBook
On this page

Was this helpful?

Export as PDF
  1. Updating and Managing

Android Studio - Deploying Code Wirelessly

PreviousAccessing Log FilesNextWelcome to Hello Robot!

Last updated 9 months ago

Was this helpful?

Android Debug Bridge (ADB) utility is the tool used by Android Studio to connect and control Android devices, like the Control Hub. Android Studio, using ADB, allows users to build and install the Robot Controller app onto their Control Hub.

By default ADB supports using a hardwire connection via USB to deploy code to Android Devices. ADB does support a wireless mode where the build and install process is sent over Wi-Fi. The Control Hub is configured to support ADB wireless connections on port 5555. To deploy code over the Wi-Fi connection the user will need to set up Wireless ADB.

Setting Up Wireless ADB using the REV Hardware Client

The Control Hub is ready to connect with a PC when the LED turns from blue to green.

Connect to the Wi-Fi Network created by the Control Hub

Open the REV Hardware Client and confirm the Control Hub is connected over Wi-Fi

The Control Hub should be listed in the Android Studio devices dropdown

To set up wireless ADB using the REV Hardware Client you will need a laptop or PC with both and the installed.

Power on the Control Hub, by plugging the 12V Slim Battery () into the XT30 connector labeled “BATTERY” on the Control Hub.

Note:

Android Studio
REV Hardware Client
REV-31-1302
Connect to the REV Hardware Client over USB if the password needs resetting.
C:\Users\Rachel\AppData\Local\Microsoft\Windows\INetCache\Content.Word\g20714.png